How To Clean A .22 Henry Rifle

A lever action rifle.

Quick Tips

Remove the receiver bolt, lever, and ejector.
Use a jag and a patch to moisten the bore with solvent.
Now utilise a wire brush to loosen the fouling.
Dry the bore with a dry patch and jag.
Lightly oil the diameter with a sparingly oiled patch and jag.
Wipe downwards the receiver and all its parts.
Reassemble the receiver and lever.
Lightly oil the outside of the unabridged rifle.

This Marlin 30-xxx is the first and but lever-action rifle I have owned. My dad gave it to me when I was thirteen years old. It was my 2nd year of deer hunting, and since I had managed to bag a deer with the single-shot 20 gauge the year before, my dad decided I was ready for a real gun. I shot four times, if you can imagine information technology. One of them striking, though, and I bagged my first buck—a spike. Information technology was good shot, too, right in the lungs. He was dead inside minutes. The next deer I shot was a doe with my thirty-30, this 1 here.

I have been using this gun for xv years now, and information technology is still in smashing shape as y'all can see from the pictures. I don't know if it's only my gun, but these puppies are heavy. I got my kickoff 30-06 this year and that matter is way lighter than this. I think it's the weight of this gun that appeals to me. Its projectile will plow through brush, whereas information technology seems the 30-06 can be deflected by the tiniest things, like a foliage for case. Just they are both tools, both with an intended purpose, and both must be clean in club to perform properly, so let's get to it.

Steps to Cleaning a Lever-Activeness Rifle

Remove the receiver commodities, lever, and ejector. Unload the weapon. Cock the hammer with the safety on. Open the leaver halfway, and remove the lever screw then the lever. Next, pull the receiver commodities out of the receiver. This will leave the ejector loose inside. Don't lose information technology. The bore may at present exist cleaned from the non-business stop of your rifle.
Use a jag and a patch to moisten the bore with solvent. Attach the appropriate-sized jag or bore mop to the ramrod. Moisten the patch or mop with bore solvent. Put the ramrod into the barrel and push it through the bore. Let the solvent soak on the bore for 10 to 20 minutes.
Now use a wire brush to loosen the fouling. Remove the jag from the ramrod and attach the appropriate-sized wire brush according to your burglarize's caliber. If you have a bore guide put that in. That but keeps fouling from getting pulled back into the receiver. If yous don't have one, just remove the brush later on you push it through, pull the ramrod out, reattach, and repeat ten to 12 times.
Dry the bore with a dry patch and jag. After sufficiently scrubbing the bore of the barrel, reattach the jag and begin pushing dry patches through. In my instance, information technology took ten patches before they came out clean. If yous don't accept a jag, apply the hoop tip to dry the diameter. Some of the cleaner patches may be flipped around and used again in order to conserve patches.
Lightly oil the diameter with a sparingly oiled patch and jag. The bore is now clean and dry, but it is vulnerable to rust. So, in gild to assistance forbid that, nosotros push button a lightly oiled patch through with the jag. If you don't have a jag, use the hoop tip instead. Be careful not to put also much oil in. Check the oil amount by holding the bore upwardly to a low-cal and looking through it.
Wipe downwardly the receiver and all its parts. The receiver of a lever-action rifle is non likely to go very dirty very apace, but accept a wait inside and see if information technology needs to be cleaned. Your gun cleaning kit should come with a brush that you could utilise to make clean the receiver if it needs information technology. Or just wipe it downwards a bit with a microfiber cloth. Practice the aforementioned with the bolt and the lever. Put a little gun grease onto the bolt to aid its motion.
Reassemble the receiver and lever. Put the ejector dorsum in its place, and slide the bolt back in where it was when you lot pulled the lever out. Slide the lever dorsum into its slot. The tip of the lever fits just inside a modest slot in the commodities. Line the lever screw hole up and put it back in. If yous need more help, await below for detailed pictures on disassembling and reassembling a lever-action rifle.
Lightly oil the outside of the entire rifle. To stop cleaning your lever-activeness burglarize, apply a lite coat of gun oil to your entire rifle. This will assistance protect all its parts from rust while you store it. If yous intend to store it long term, consider getting a hardshell case. The material cases tend to blot oil over time, leaving your rifle vulnerable to rust. Too, they offer more protection than a standard material instance.

How to Remove the Lever and Commodities of a Lever-Action Burglarize

Unload the rifle, set the rubber, and cock the hammer.
Open the lever halfway.
Remove the lever screw.
Pull the bolt out. You may have to push the hammer down to get it by it.
Remove the ejector. And y'all're done. Reverse this procedure to put your rifle back together.

Gun Cleaning Products

The jag kit plus the regular cleaning kit. Not all cleaning kits come with a jag kit, only they are sold separately for effectually 13 dollars. The jag is far superior to other methods of removing solvent and loosened fouling. Just make certain to utilize the proper quotient/guess. And always keep your tools clean.

Hoppe's ix Bench Rest Copper Solvent is specifically formulated to remove stuck-on copper from rifle barrels. Copper may come from the jackets of bullets. The copper solvent also removes pb and fouling. Y'all can find Hoppe's Bench Residuum No. 9 from Amazon.

silver bore snake A diameter snake is one possible solution to someone who either cannot or does non desire to remove the bolt and or lever. But drop the weighted string down the barrel and pull information technology through. Always run the bore serpent abroad from the receiver to go on filth from getting in information technology.